Rockford Fosgate bd1000.1 User Manual

mono amplifier operation & installationPower bd1500.1Power bd1000.1Power bd500.1

7Mounting LocationThe mounting location and position of your amplifier will have a greateffect on its ability to dissipate the heat generated during n

8Battery and ChargingAmplifiers will put an increased load on the vehicle's battery and chargingsystem. We recommend checking your alternator and

93. Strip 3/8" from the battery end of the power cable and crimp a large ringterminal to the cable. Use the ring terminal to connect to the batte

10Installation Power ConnectionsMono Mode• RCA inputs are connected to both left and right inputs•Speaker Impedance should be 2Ω minimum

11Crossover OperationPunch Bass Operation• Carefully increase potentiometer to add Punch to your bass frequencies• Exercise caution when increasing Pu

12• Pass-Thru feeds signal to secondary amplifier•Signal from Pass-Thru remains stereoPass-Thru

13Bridging Mode(use bd sync kit) • Connect the two NEG Speaker outputs together using an eight gauge wire no longer than 15”.• When bridging

14TroubleshootingIf you are having problems after installation follow theTroubleshooting procedures below.Procedure 1: Check Amplifier for proper conn

15Limited Warranty InformationRockford Corporation offers a limited warranty on Rockford Fosgate products on thefollowing terms:• Length of Warranty3

16ESPAÑOLLEA DETENIDAMENTE LAS SIGUIENTES INSTRUCCIONES DE INSTALA-CION DEL PRODUCTO. EVITARA POSIBLES DAÑOS A VD., AL VEHICU-LO O AL PRODUCTO.Montaje

iDear Customer,Congratulations on your purchase of the world's finest brand of car audio amplifiers.At Rockford Fosgate we are fanatics about mus

17• Las entradas RCA se conectan a ambos canales izquierdo yderecho• La impedancia minima mono debe ser 2Ω.• Los Divisores de Frecuencia Variable pued

18FRANÇAISATTENTION: Veuillez lire les instructions suivantes pour l'installation decet amplifcateur. Ne pas les suivre pourrait causer des bless

19Terminal B+Il est impératif qu'il y ait un fusible sur le câble pour la connexion à lamasse. Préparez le châssis en grattant la peinture de la

20DEUTSCHBITTE LESEN SIE DIESE GEBRAUCHSANLEITUNG ZUERST SORGFÄLTIGDURCH. DAS KANN SIE VOR DEM FALSCHEN EINSATZ, AUSFALLENODER SOGAR BESCHÄDIGUNG DES

21B+ AnschlubDie Plus-Leitung MUb ca. 40 cm nach dem Plus-Pol der Batterieabgesichert sein. Preparieren Si die Kabellängen und montieren Sie denSicher

22ITALIANOATTENZIONE: SI PREGA DI LEGGERE LE SEGUENTI ISTRUZIONI PERL'INSTALLAZIONE DI QUESTO PRODOTTO. IL NON SEGUIRLEPOTREBBE RISULTARE SERIAME

23Terminale B+ (cavo positivo)Il cavo positivo deve essere protetto da un fusibile a non piú di 45 cm dallabatteria. Terminare il cavo e installare il

24Notes

9/00 M.J.TMAN-3154-BRockford Corporation546 South Rockford DriveTempe, Arizona 85281 U.S.A.In U.S.A., (480) 967-3565 In Europe, Fax (49) 8503-9340

iiTable of ContentsSpecifications...1Introduction ...

1Specifications*recommended fuse not suppliedSystem Model bd500.1 bd1000.1 bd1500.1Frequency Response: 10-250Hz ± 3dB 10-250Hz ± 3dB 10-250Hz ± 3dBBa

2Amplifier Accessory PackThe accessory pack included with each amplifier contains the mountinghardware necessary to secure the amp to the vehicle and

3Power Mono Amplifier Feature ChartPOWER AMPLIFIER# of Channels 1Stable Into: (mono) 2ΩCIRCUITRYClass bdMEHSA1- heat dissipating technologyTOPAZ2- pat

4Design FeatureS1. Cast Aluminum Heatsink – The cast aluminum heatsink of the Punchamplifier dissipates heat generated by the amplifier's circui

56. RCA Pass-Thru Jacks – The Pass-Thru provides a convenient source fordaisy-chaining an additional amplifier without running an extra set ofRCA cabl

6Installation ConsiderationsThis section focuses on some of the vehicle considerations for installingyour new Punch amplifier. Checking your battery